Reference manual
Copyright
This document is Copyright © 2019 by it’s contributors as listed below. You may distribute it and/or modify it under the terms of either the GNU General Public License (http://www.gnu.org/licenses/gpl.html), version 3 or later, or the Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0/), version 3.0 or later.
Contributors
Heitor de Bittencourt. Mathias Neumann
Feedback
Please direct any bug reports, suggestions or new versions to here:

About KiCad document: https://github.com/KiCad/kicaddoc/issues

About KiCad software: https://bugs.launchpad.net/kicad

About KiCad software i18n: https://github.com/KiCad/kicadi18n/issues
Publication date and software version
july 17, 2019
Introduction
The KiCad PCB Calculator is a set of utilities to help you find the values of components or other paremeters of a layout. The Calculator has the following tools:

Regulators

Track Width

Electrical Spacing

Trans Line

RF Attenuators

Color Code

Board Classes
Calculators
Regulators
This calculator helps with the task of finding the values of the resistors needed for linear and lowdropout voltage regulators.
For the Standard Type, the output voltage Vout as a function of the reference voltage Vref and resistors R1 and R2 is given by:
For the 3 terminal type, there is a correction factor due to the quiescent current Iadj flowing from the adjust pin:
This current is typically below 100 uA and can be neglected with caution.
To use this calculator, enter the parameters of the regulator Type, Vref and, if needed, Iadj, select the field you want to calculate (one of the resistors or the output voltage) and enter the other two values.
TrackWidth
The Track Width tool calculates the trace width for printed circuit board conductors for a given current and temperature rise. It uses formulas from IPC2221 (formerly IPCD275).
ElectricalSpacing
This table helps finding the minimum clearance between conductors.
Each line of the table has a minimum recomended distance between conductors for a given voltage (DC or AC peaks) range. If you need the values for voltages higher than 500V, enter the value in the box in the left corner and press Update Values.
TransLine
Transmission line theory is a cornerstone in the teaching of RF and microwave engineering.
In the calculator you can choose different sorts of Line Types and their special parameters. The models implemented are frequencydependent, so they disagree with simpler models at high enough frequencies.
This calculator is heavilly based on Transcalc.
The transmission line types and the reference of their mathematical models are listed below:

Microstrip line:

H. A. Atwater, “Simplified Design Equations for Microstrip Line Parameters”, Microwave Journal, pp. 109115, November 1989.


Coplanar wave guide.

Coplanar wave guide with ground plane.

Rectangular waveguide:

S. Ramo, J. R. Whinnery and T. van Duzer, "Fields and Waves in Communication Electronics", WileyIndia, 2008, ISBN: 9788126515257.


Coaxial line.

Coupled microstrip line:

H. A. Atwater, “Simplified Design Equations for Microstrip Line Parameters”, Microwave Journal, pp. 109115, November 1989.

M. Kirschning and R. H. Jansen, "Accurate WideRange Design Equations for the FrequencyDependent Characteristic of Parallel Coupled Microstrip Lines," in IEEE Transactions on Microwave Theory and Techniques, vol. 32, no. 1, pp. 8390, Jan. 1984. doi: 10.1109/TMTT.1984.1132616.

Rolf Jansen, "HighSpeed Computation of Single and Coupled Microstrip Parameters Including Dispersion, HighOrder Modes, Loss and Finite Strip Thickness", IEEE Trans. MTT, vol. 26, no. 2, pp. 7582, Feb. 1978.

S. March, "Microstrip Packaging: Watch the Last Step", Microwaves, vol. 20, no. 13, pp. 83.94, Dec. 1981.


Stripline.

Twisted pair.
RFAttenuators
With the RF Attenuator utility you can calculate the values of the resistors needed for different types of attenuators:

PI

Tee

Bridged Tee

Resistive Splitter
To use this tool, first select the type of attenuator you need, then enter the desired attenuation (in dB) and input/output impedances (in Ohms).
ColorCode
This calculator helps translating the color bars from the resistor to its value. To use it, first select the tolerance of the resistor: 10%, 5% or equal or smaller than 2%. For example:

Yellow Violet Red Gold: 4 7 x100 ±5% = 4700 Ohm, 5% tolerance

1kOhm, 1% tolerance: Brown Black Black Brown Brown